Gomados+ bricked ? Help needed

Dudas, cuestiones, sugerencias y peticiones en general sobre el proyecto / Questions and requests about the project
GiacV
Mensajes: 7
Registrado: 10 May 2021, 23:08

Gomados+ bricked ? Help needed

Mensaje por GiacV » 10 May 2021, 23:32

Hello ! I need help.
I updated the firmware on my Gomados+ and the operation was apparently ok (according to the message I received from bios), but after restart
the machine remained frozen on the test color pattern, and so it's now.
I tried to recover with Windows and Usb-Blaster, with no success (the jtag software seems to obtain response from Gomados and the leds change their state, but the bios isn't shown on the display).
Here is what I obtain from jtag.exe, after the "pld load" command :
Adjuntos
jtag.exe screenshot.jpg

Avatar de Usuario
antoniovillena
Mensajes: 2621
Registrado: 27 Sep 2015, 20:41

Re: Gomados+ bricked ? Help needed

Mensaje por antoniovillena » 11 May 2021, 00:23

GiacV escribió:
10 May 2021, 23:32
Hello ! I need help.
I updated the firmware on my Gomados+ and the operation was apparently ok (according to the message I received from bios), but after restart
the machine remained frozen on the test color pattern, and so it's now.
I tried to recover with Windows and Usb-Blaster, with no success (the jtag software seems to obtain response from Gomados and the leds change their state, but the bios isn't shown on the display).
Here is what I obtain from jtag.exe, after the "pld load" command :
The command is correct but the signal is 15khz instead 31khz (VGA). To switch press ScrollLock on keyboard. You must see BIOS on display and continue recovery process.

Avatar de Usuario
Kyp
Mensajes: 240
Registrado: 18 May 2016, 20:16

Re: Gomados+ bricked ? Help needed

Mensaje por Kyp » 11 May 2021, 15:22

You are apparently trying to write an LX16 bitstream but your board has an LX25 chip.

azesmbog
Mensajes: 319
Registrado: 17 Feb 2016, 23:07

Re: Gomados+ bricked ? Help needed

Mensaje por azesmbog » 11 May 2021, 23:02

Kyp escribió:
11 May 2021, 15:22
You are apparently trying to write an LX16 bitstream but your board has an LX25 chip.
Он делает все правильно. И надо действительно нажать ScrollLock

GiacV
Mensajes: 7
Registrado: 10 May 2021, 23:08

Re: Gomados+ bricked ? Help needed

Mensaje por GiacV » 12 May 2021, 01:45

Unfortunately no success.
The board seems to be alive (I can hear the classic Zx Spectrum key clutter when I press a key), but when I execute the "pld load" command the color test pattern goes away and all becomes black, then I press ScrollLock and the damned color test pattern is back again ....

azesmbog
Mensajes: 319
Registrado: 17 Feb 2016, 23:07

Re: Gomados+ bricked ? Help needed

Mensaje por azesmbog » 14 May 2021, 15:20

Судя по картинке - Вы делаете все правильно.
Сейчас попробовал еще раз залить recovery.zxd.bit
У меня подключено к монитору. И при заливке показывает сразу горизонтальные цветные полосы, но это картинка самого монитора, потому что синхронизация неверная. При нажатии ScrollLock включается BIOS.
Могу посоветовать залить напрямую какое-нибудь ядро, любое )
Наверное можно залить и последнее ядро Spectrum и из него попробовать восстановить flash - но такой фокус я пока не пробовал :)

GiacV
Mensajes: 7
Registrado: 10 May 2021, 23:08

Re: Gomados+ bricked ? Help needed

Mensaje por GiacV » 15 May 2021, 15:46

azesmbog escribió:
14 May 2021, 15:20
Судя по картинке - Вы делаете все правильно.
Сейчас попробовал еще раз залить recovery.zxd.bit
У меня подключено к монитору. И при заливке показывает сразу горизонтальные цветные полосы, но это картинка самого монитора, потому что синхронизация неверная. При нажатии ScrollLock включается BIOS.
Могу посоветовать залить напрямую какое-нибудь ядро, любое )
Наверное можно залить и последнее ядро Spectrum и из него попробовать восстановить flash - но такой фокус я пока не пробовал :)
I understand what you are suggesting, but I'm not sure how to do it; so if you can show a procedure to do that, i will be very grateful to you.

Я понимаю, что вы предлагаете, но не знаю, как это сделать; так что если вы сможете показать процедуру для этого, я буду вам очень благодарен.

azesmbog
Mensajes: 319
Registrado: 17 Feb 2016, 23:07

Re: Gomados+ bricked ? Help needed

Mensaje por azesmbog » 18 May 2021, 21:09

GiacV escribió:
15 May 2021, 15:46
I understand what you are suggesting, but I'm not sure how to do it; so if you can show a procedure to do that, i will be very grateful to you.
Я предлагаю проверить на любом другом ядре как работает Ваша Gomados +
Суть в том, что через интерфейс JTAG можно загрузить не только recovery ядро, но и вообще любое ядро.
Насколько я понимаю, когда грузится recovery.zxd.bit - то экран становится черным??
Попробуйте загрузить через JTAG тестовое ядро
https://drive.google.com/file/d/1HEaSuG ... sp=sharing
оно загружается той же самой командой

Código: Seleccionar todo

pld load test_placa_lx25.bit
Если все загрузилось верно, то Вы должны увидеть красивую картинку
Imagen
а также услышать звук и увидеть мигающий светодиод.
Если звук есть, но нет изображения - можно попытаться нажать клавиши 1,2 или 3
Если тест загружается и все видно и работает - таким же образом можно попытаться загрузить основной файл SPECTRUM. Ну и думать дальше ))

GiacV
Mensajes: 7
Registrado: 10 May 2021, 23:08

Re: Gomados+ bricked ? Help needed

Mensaje por GiacV » 21 May 2021, 15:54

The test is loaded and visible, and, as you can see, I obtain an error on the sdram one. What does it mean ?

Тест загружен и виден, и, как видите, я получаю ошибку на SDRAM. Что это значит ?
Test zagruzhen i viden, i, kak vidite, ya poluchayu oshibku na SDRAM. Chto eto znachit ?
Adjuntos
screen test.jpg
screen test.jpg (44.16 KiB) Visto 3805 veces

azesmbog
Mensajes: 319
Registrado: 17 Feb 2016, 23:07

Re: Gomados+ bricked ? Help needed

Mensaje por azesmbog » 21 May 2021, 20:30

Ну это вообще отличный результат !
Значит прошивки загружаются верно.
не понятно, почему recovery - прошивка неправильно загружается.
Это вопрос конечно к авторам, например в Антонио.
Но я бы еще попробовал таким образом загрузить обычную прошивку ядра Spectrum и зайти в bios и попробовать восстановить flash. попытка - не пытка, и хуже точно уже не будет :)

SDRAM тест выдает ошибку - это совершенно не важно, возможно на вашей плате SDRAM не установлена, или установлена по другим адресам пинов. В другой ветке есть тест SDRAM - можно потом проверить им.
https://drive.google.com/file/d/12ZW9pN ... sp=sharing

Вот совершенно официальное ядро Spectrum, без всяких моих исправлений :)
https://drive.google.com/file/d/1uusgnO ... sp=sharing
Попробуйте залить его через JTAG и войти в BIOS
Возможно после загрузки ничего не получится, flash то испорченный, но почему бы и не попробовать?))

Responder