Actualización conjunta experimental de Firmware 0.75 y core EXP26
- desUBIKado
- Mensajes: 1002
- Registrado: 05 Ago 2016, 22:33
Re: Actualización conjunta experimental de Firmware 0.73 y core EXP26
Cierto, la última versión del core EXP26 para 2 MiB externos instalado como principal hace que luego, independientemente del core que elijas, siempre acabe arrancando el core de Spectrum. Como "workaround" se puede instalar la versión de 512 K, pero quedamos a la espera de que Antonio, cuando pueda, saque una nueva versión que no tenga ese problema
Re: Actualización conjunta experimental de Firmware 0.73 y core EXP26
Hello. New user here. I've updated to bios 0.72 downloaded from the official 'descargas' link, however at that moment i had seen no warning that the core had to be upgraded simultaneously.
After the bios update, the device boots ok to the command prompt however keyboard is non responsive (using rubber keyboard with zxuno xl inside inside a spectrum case). If i press any key during boot to try enter bios setup, the boot process freezes.
Would it work if I get hold of a ps\2 keyboard? Any suggestions to access the bios and reflash? Thanks!!
Replies in Spanish are ok too
After the bios update, the device boots ok to the command prompt however keyboard is non responsive (using rubber keyboard with zxuno xl inside inside a spectrum case). If i press any key during boot to try enter bios setup, the boot process freezes.
Would it work if I get hold of a ps\2 keyboard? Any suggestions to access the bios and reflash? Thanks!!
Replies in Spanish are ok too
Re: Actualización conjunta experimental de Firmware 0.73 y core EXP26
Hola - soy nuevo usuario de ZX-Uno XL
Ayer hice el update de firmware a version 0.72, obtenido del link oficial 'descargas'
No habia ningun aviso como en el 0.73 de posible briqueo en caso de no actualizar junto al Core ZX. Sin embargo, luego de flashear la BIOS, el teclado no responde (utilizo teclado de goma con membrana en una ZX case) - el sistema bootea correctamente hasta el command prompt de Spectrum pero no responde a las teclas. Si intento ingresar al Setup durante la pantalla de boot inicial, el proceso de boot se congela al presionar las teclas respectivas.
Es posible que el Firmware 0.72 tenga los mismos requerimientos que el 0.73 y que produzca bloqueo de teclado? Y de ser asi, tengo esperanzas de poder utilizar el sistema si conecto un teclado PS/2?
Caso contrario, agradezco sugerencias e indicaciones de como re-flashear el firmware a una version que me permita recuperar el sistema.
Desde ya muchas gracias.
Ayer hice el update de firmware a version 0.72, obtenido del link oficial 'descargas'
No habia ningun aviso como en el 0.73 de posible briqueo en caso de no actualizar junto al Core ZX. Sin embargo, luego de flashear la BIOS, el teclado no responde (utilizo teclado de goma con membrana en una ZX case) - el sistema bootea correctamente hasta el command prompt de Spectrum pero no responde a las teclas. Si intento ingresar al Setup durante la pantalla de boot inicial, el proceso de boot se congela al presionar las teclas respectivas.
Es posible que el Firmware 0.72 tenga los mismos requerimientos que el 0.73 y que produzca bloqueo de teclado? Y de ser asi, tengo esperanzas de poder utilizar el sistema si conecto un teclado PS/2?
Caso contrario, agradezco sugerencias e indicaciones de como re-flashear el firmware a una version que me permita recuperar el sistema.
Desde ya muchas gracias.
- antoniovillena
- Mensajes: 2621
- Registrado: 27 Sep 2015, 20:41
Re: Actualización conjunta experimental de Firmware 0.73 y core EXP26
Acabo de sacar una que no tiene ese problema. En el zip del primer mensaje del hilo. Espero que no tenga ningún otro problema.desUBIKado escribió:pero quedamos a la espera de que Antonio, cuando pueda, saque una nueva versión que no tenga ese problema
- antoniovillena
- Mensajes: 2621
- Registrado: 27 Sep 2015, 20:41
Re: Actualización conjunta experimental de Firmware 0.73 y core EXP26
Hi chilo. Connect a joystick and try to upgrade new core (or old firmware) from BIOS. To enter BIOS press joystick down during splash screen. Then, in the core boot menu select last option (Enter Setup). And the go to the Upgrade menu and desired option.chilo escribió:Hello. New user here. I've updated to bios 0.72 downloaded from the official 'descargas' link, however at that moment i had seen no warning that the core had to be upgraded simultaneously.
After the bios update, the device boots ok to the command prompt however keyboard is non responsive (using rubber keyboard with zxuno xl inside inside a spectrum case). If i press any key during boot to try enter bios setup, the boot process freezes.
Would it work if I get hold of a ps\2 keyboard? Any suggestions to access the bios and reflash? Thanks!!
Replies in Spanish are ok too
If that doesn't work, try the unbrick method on this guide:
http://uto.speccy.org/zxunofaq_en.html#unbrick
- desUBIKado
- Mensajes: 1002
- Registrado: 05 Ago 2016, 22:33
Re: Actualización conjunta experimental de Firmware 0.73 y core EXP26
Ya lo he instalado y ya se puede arrancar cualquier otro core sin problemas. Muchas gracias por todo el trabajo que estás haciendo dándonos soporte.antoniovillena escribió:Acabo de sacar una que no tiene ese problema. En el zip del primer mensaje del hilo. Espero que no tenga ningún otro problema.desUBIKado escribió:pero quedamos a la espera de que Antonio, cuando pueda, saque una nueva versión que no tenga ese problema
Re: Actualización conjunta experimental de Firmware 0.73 y core EXP26
Thanks for the info!antoniovillena escribió:Hi chilo. Connect a joystick and try to upgrade new core (or old firmware) from BIOS. To enter BIOS press joystick down during splash screen. Then, in the core boot menu select last option (Enter Setup). And the go to the Upgrade menu and desired option.chilo escribió:Hello. New user here. I've updated to bios 0.72 downloaded from the official 'descargas' link, however at that moment i had seen no warning that the core had to be upgraded simultaneously.
After the bios update, the device boots ok to the command prompt however keyboard is non responsive (using rubber keyboard with zxuno xl inside inside a spectrum case). If i press any key during boot to try enter bios setup, the boot process freezes.
Would it work if I get hold of a ps\2 keyboard? Any suggestions to access the bios and reflash? Thanks!!
Replies in Spanish are ok too
If that doesn't work, try the unbrick method on this guide:
http://uto.speccy.org/zxunofaq_en.html#unbrick
I am able to boot with the joystick combination and get into the recovery screen of the Boot Core (the vertical color bars screen that say "ZX-UNO Spectrum core is loaded. Now trying to boot from BIOS. You shouldn't see this screen fro more than half a second").
Unfortunately I don't see an option to select "Setup" and I believe the Core is waiting for a TAP signal to load a BIOS. Is that right?
As I read in the forum, at that stage only the Core has loaded and not the BIOS , hence the potentially corrupted BIOS is not active and I should be able to perform the recovery with a TAP firmware via EAR. However , nothing happens as I play the TAP... i see no load bars or any sign of activity. Is there something I need to do to make the Boot Core load the TAP at this stage?
Thanks again
- antoniovillena
- Mensajes: 2621
- Registrado: 27 Sep 2015, 20:41
Re: Actualización conjunta experimental de Firmware 0.73 y core EXP26
Download this file. Copy the FIRMWARE.ZX1 to the SD of your ZX-Uno and play the FIRMWARE.TAP with a TAP loader from a PC to the ZX via EAR and recovery method. Stay alert when the load finish to press F2. So if you succefully enter to BIOS go to "Update Firmware by SD". After that your ZX-Uno will respond and you will able to upgrade both BIOS and CORE by .COREBIOS method.
- Adjuntos
-
- firmware.0.59.zip
- (20.96 KiB) Descargado 263 veces
Re: Actualización conjunta experimental de Firmware 0.73 y core EXP26
Thanks, but I can't get the tape to start loading when I am in the recovery screen. What am I doing wrong?
- antoniovillena
- Mensajes: 2621
- Registrado: 27 Sep 2015, 20:41
Re: Actualización conjunta experimental de Firmware 0.73 y core EXP26
Maybe the tool you don't output enough signal level. Are you using the EAR jack? I don't know where is exactly in XL but is different to the AUDIO out (but the connector is the same). I have created a WAV file. Use this file and play it with VLC (this will output at max level).chilo escribió:Thanks, but I can't get the tape to start loading when I am in the recovery screen. What am I doing wrong?
- Adjuntos
-
- firmware.zip
- (106.6 KiB) Descargado 257 veces