Vendo placas adaptadoras para UnAmiga
Re: Vendo placas adaptadoras para UnAmiga de jepalza
Does "hat" mean "pcb board with connector"? I translated it into English so I could not answer accurately.
I will purchase the FPGA directly from the link to aliexpress. I want "las placas de conectores montadas".
I will purchase the FPGA directly from the link to aliexpress. I want "las placas de conectores montadas".
- antoniovillena
- Mensajes: 2621
- Registrado: 27 Sep 2015, 20:41
Re: Vendo placas adaptadoras para UnAmiga de jepalza
I immediately ordered it with PayPal. I saw the shop site, there were other products of inteest with the ZXUno option.
By the way, there was no pin attached to the FPGA that was exhibited at Aliexpress. It was necessary to send an "solder the pin to the front" message to the seller.
By the way, there was no pin attached to the FPGA that was exhibited at Aliexpress. It was necessary to send an "solder the pin to the front" message to the seller.
Re: Vendo placas adaptadoras para UnAmiga de jepalza
Hello all, I recently assembled UnAmiga, but I didn't want to have bare electronics on table so I modeled a case for it. If anyone else wants it, models for 3D printing can be downloaded on thingiverse.
Also, if any of the non Spanish users wants to try it, I tried translating Mist AGA menu to English, it can be downloaded from ForoFPGA forum
Pictures:
https://imgur.com/a/oZYL6BW
*edit*
I uploaded pictures to Imgur, so post wouldn't be so big
Also, if any of the non Spanish users wants to try it, I tried translating Mist AGA menu to English, it can be downloaded from ForoFPGA forum
Pictures:
https://imgur.com/a/oZYL6BW
*edit*
I uploaded pictures to Imgur, so post wouldn't be so big
Re: Vendo placas adaptadoras para UnAmiga
I received private message about where to print this case, but I can't send private messages so I can't reply that way.
Unfortunately I don't know where can one order 3D prints and how much prints cost. I have 3D printer so I printed it myself.
I can only say that it takes between 25 to 30 meters of filament (1,75 mm type) to print it. For PLA plastic (which is mostly used) price of this filament length comes between 2,5€ and 3€, depending on brand.
At 50 mm/s print speed it takes about 12 hours to print everything and depending on printer it uses 100-150 W to print so it uses 1 - 1,5 kWh of power.
Maybe that can help you to calculate if print service price is OK or not.
Unfortunately I don't know where can one order 3D prints and how much prints cost. I have 3D printer so I printed it myself.
I can only say that it takes between 25 to 30 meters of filament (1,75 mm type) to print it. For PLA plastic (which is mostly used) price of this filament length comes between 2,5€ and 3€, depending on brand.
At 50 mm/s print speed it takes about 12 hours to print everything and depending on printer it uses 100-150 W to print so it uses 1 - 1,5 kWh of power.
Maybe that can help you to calculate if print service price is OK or not.
Re: Vendo placas adaptadoras para UnAmiga
Ah, he sido yo. Me gusta bastante la caja. No se cuantos mensajes hay que publicar para poder enviar privados. Creo que dos que tres.
Muchas gracias Solo761.
Muchas gracias Solo761.
Re: Vendo placas adaptadoras para UnAmiga
Hola a todos!, soy nuevo y también soy un 'old school' que disfrutó del amiga en sus tiempos de gloria.
Lo primero felicitar a jepalza y a antoniovillena por vuestro tremendo trabajo!
Y por otra parte, estaría interesado en adquirir uno completo (fpga + hat + caja metacrilato) o probablemente dos si aún estoy a tiempo, si que he visto en la tienda de antoniovillena el hat, pero no estoy seguro del resto.
Gracias por todo!
Lo primero felicitar a jepalza y a antoniovillena por vuestro tremendo trabajo!
Y por otra parte, estaría interesado en adquirir uno completo (fpga + hat + caja metacrilato) o probablemente dos si aún estoy a tiempo, si que he visto en la tienda de antoniovillena el hat, pero no estoy seguro del resto.
Gracias por todo!
- antoniovillena
- Mensajes: 2621
- Registrado: 27 Sep 2015, 20:41
Re: Vendo placas adaptadoras para UnAmiga
HolaEdgg escribió:Hola a todos!, soy nuevo y también soy un 'old school' que disfrutó del amiga en sus tiempos de gloria.
Lo primero felicitar a jepalza y a antoniovillena por vuestro tremendo trabajo!
Y por otra parte, estaría interesado en adquirir uno completo (fpga + hat + caja metacrilato) o probablemente dos si aún estoy a tiempo, si que he visto en la tienda de antoniovillena el hat, pero no estoy seguro del resto.
Gracias por todo!
Yo te puedo vender el hat+caja de metacrilato. La placa fpga la tendrías que comprar por tu cuenta en el enlace de aliexpress que hay en el primer mensaje del hilo. El hat y la caja son 35 euros con envío incluido. Te paso detalles de pago por privado.
Re: Vendo placas adaptadoras para UnAmiga
Estupendo Antonio, 2x 35 al final,
no puedo escribir privados, si necesitas algo escríbeme privado tu a mi.
Gracias!
no puedo escribir privados, si necesitas algo escríbeme privado tu a mi.
Gracias!
Re: Vendo placas adaptadoras para UnAmiga
Ya me han llegado las placas de China, en los próximos días me pondré a configurar ambos sistemas,
Gracias a todos!
Gracias a todos!